Mastering Basic Plumbing When You Install a Bathtub
Mastering Basic Plumbing When You Install a Bathtub
Blog Article
Were you trying to find information and facts around A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately difficult job. If the old tub is conveniently accessible, the job can move quickly; if you have to open up a wall to get rid of the old tub as well as position the brand-new bathtub, the job is much harder. In either case, the project is within a home handyman's abilities, although you will require a helper to move out the old tub and embeded in the brand-new one. Make sure you have qualified on your own for the work and fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed job, it is far better to take into consideration using one before you start. Chances are you may require a specialist plumber to make tube connections.
This article will certainly help you set up a new bathtub in your washroom if you have currently bought a new bathtub and don't require to transform the plan of your previous water system pipes.
Your tools and product checklist ought to comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, then the first thing you must do is disconnect the water supply. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted access that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in location in between the tap and also the sink. Protect the faucet in position with the producer given backnut. As soon as the faucet is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical tap adapters. The previous kind must be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Bath tub
Making use of both wooden boards under its feet, put the bathtub in the required placement. The wood boards are helpful in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 small points.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the tub until the level checks out degree.
To set up taps, fit the bottom of the outermost adaptable tap port to the proper supply pipe by making a compression join; after that do the very same for the other tap.
Switch on the supply of water and check all joints and also new pipework for leakages and tighten them if essential. Load the bath tub and likewise inspect the overflow outlet and also the typical electrical outlet for leakages.
Lastly, deal with the bathroom paneling as defined in the supplier's instruction manual. Tiling and also securing around the bath tub ought to wait until the bathtub has actually been used at the very least once as this will settle it into its final placement.
Planning for the Installment
Firstly, the supporting frame provided with the bath ought to be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to make certain that if the tap includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the faucets unit to prevent pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its final position.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to break a rigid seal, causing the water to permeate the wall surface in between the bathroom as well as the tiling, causing issues with wetness and feasible leaks to the ceiling below.
You can choose from a range of coloured sealers to blend in your components as well as fittings. They are sold in tubes and cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bath tub with water prior to securing, to permit the movement experienced when the tub remains in use. The sealer can crack rather very early if you do not take into account this motion before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently readily available on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that blog entry on How to Install a Bathtub Yourself while doing a lookup on the search engines. Feel free to take the opportunity to distribute this entry if you appreciated it. I take joy in reading our article about Installing A Bathtub.
Browse Our Site Report this page